Alvarion Wi^2 AP CLI Specifications Page 140
- Page / 248
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
118 BreezeMAX Wi² and BreezeACCESS Wi² System Manual
Chapter 7 - Network Configuration
7.5 DNS
The AP provides several options to customize DNS handling. To configure these
options, select Network > DNS.
7.5.1 DNS Servers
Server 1: Specify the IP address of the primary DNS server for the AP to use.
Server 2: Specify the IP address of the secondary DNS server for the AP to use.
7.5.2 DNS Advanced Settings
7.5.2.1 DNS Cache
Enable this checkbox to activate the DNS cache. Once a host name is successfully
resolved to an IP address by a remote DNS server, it is stored in the cache. This
speeds up network performance, because the remote DNS server does not have to
be queried for subsequent requests for this host.
An entry stays in the cache until one of the following is true:
An error occurs when connecting to the remote host
The time to live (TTL) of the DNS request expires
The AP restarts
Figure 7-8: DNS
- BreezeMAX Wi² 1
- System Manual 1
- Document History 2
- Legal Rights 3
- Disclaimer 4
- Limitation of Liability 5
- Important Notice 7
- Compliances 9
- EC Conformance Declaration 10
- About This Manual 11
- Contents 15
- and BreezeACCESS VL Wi 16
- System Manual 16
- Chapter 4 - Getting Started 17
- Chapter 11 - Maintenance 21
- Appendix A - Troubleshooting 21
- 1.1 Introduction 24
- 1.2 Specifications 26
- 1.2.2 Sensitivity 27
- 1.2.3 8 dBi Omni Antenna 27
- 1.2.5 Mechanical 29
- 1.2.6 Electrical 29
- 1.2.7 Connectors and LEDs 30
- 1.2.8 Environmental 30
- 1.2.9 Standards Compliance 31
- 2.1 Hardware Description 34
- 2.1.1 Bottom Panel 35
- 2.1.2 Top Panel 36
- 2.1.3 LED Indicators 36
- 2.1.3.2 Controlled Mode 37
- 2.2 Installation Requirements 38
- Installation Requirements 39
- 2.3 Installation 41
- Installation 43
- BreezeACCESS SU-ODU 46
- 2.3.5 Mounting the Wi² Unit 50
- 2.3.9.2 Configuring the Wi² 54
- Extender 57
- 3.1.1 Ethernet Port 58
- 3.1.2 Console Port 58
- 3.1.3 Grounding Point 58
- 3.1.4 Water Tight Test Point 58
- Ethernet 59
- Link/Activity 59
- 3.2 Installation Requirements 60
- Thread the steel-band 62
- Mounting the Wi² Extender ODU 63
- Secure the rectangular 64
- Wi² Extender using the 64
- Strap the steel-band 65
- Tighten the steel-band 66
- Extender to the pole 66
- 3.4.1 Grounding Wire 67
- Ethernet cable 70
- AC power 70
- 4.1 Introduction 74
- 4.2 Configuration Procedure 75
- Configuration Procedure 77
- 5.1 Key Concepts 84
- 5.1.1.1 User Authentication 85
- Service Controller 88
- 5.1.3 Management with VLANs 89
- 5.3.1 Virtual AP 94
- 5.3.2 Egress VLAN 95
- 5.3.4 Wireless Protection 97
- 5.3.4.2 802.1X 98
- Enabled Disabled 100
- 5.3.8 Wireless IP Filter 101
- 5.4 Virtual Network Data Flow 102
- 5.4.1 Stand-alone Deployment 103
- Controller 103
- 5.4.2.3 Egress 104
- 5.4.3.1 Ingress 104
- 5.4.2.2 Features 104
- 5.4.3.2 Features 105
- 5.4.3.3 Egress 105
- 5.5 Quality of Service (QoS) 106
- 5.5.1.2 802.1p 107
- 5.5.1.5 TOS 108
- 5.5.1.6 IP QoS 108
- 5.5.1.7 Disabled 109
- 5.5.1.8 QoS Example 109
- In This Chapter: 111
- 6.1 Wireless Coverage 112
- 6.1.2.2 Antenna Configuration 113
- 6.1.2.3 Interference 113
- 6.1.3.2 Selecting Channels 115
- Wireless Coverage 117
- 6.2 Conducting a Site Survey 119
- Conducting a Site Survey 121
- 6.3 Radio Configuration 122
- 6.3.1.1 Operating mode 123
- 6.3.1.2 Wireless Mode 123
- 6.3.1.3 Channel 123
- 6.3.1.4 Interval 124
- 6.3.1.5 Time of Day 124
- 6.3.1.7.2 RTS Threshold 125
- 6.3.1.7.3 Multicast Tx Rate 125
- 6.3.1.7.4 Antenna Selection 125
- 6.3.1.7.5 Beacon Interval 126
- 6.3.1.7.6 Spectralink VIEW 126
- 7.1 Port Configuration 130
- Port Configuration 131
- 7.1.3 Port Configuration 132
- 7.1.3.2 Link 133
- 7.2 VLAN Support 134
- 7.2.3 VLAN Bridging 135
- 7.2.4 VLAN Configuration 136
- 7.2.4.1 General 137
- 7.2.4.2 Assign IP Address Via 137
- 7.3 Bandwidth Control 138
- 7.5.1 DNS Servers 140
- 7.5.2 DNS Advanced Settings 140
- 7.5.2.3 DNS Switch Over 141
- 7.5.2.4 Logout Host Name 141
- 7.6 IP Routes 142
- 7.6.1.2 Default Routes 143
- 7.7 IP QoS 144
- 7.7.1.1 Settings 145
- 7.7.2 Example 146
- 4 Select Save 148
- Chapter 8 - Management 149
- 8.1 Management Tool 150
- Management Tool 151
- 8.1.3.3 Login Control 152
- 8.1.3.4 Web Server 153
- 8.1.3.5 Security 153
- Auto-refresh icon 154
- 8.2 SNMP 155
- 8.2.1.1 Attributes 156
- 8.2.1.2 Agent 156
- 8.2.1.3 Security 156
- 8.2.1.4 Traps 157
- 8.3 SOAP 158
- 8.3.1.2 Security 159
- 8.4.1 Configuring CLI Support 160
- 8.5 System Time 162
- 8.6 Country 163
- Chapter 9 - Security 165
- 9.1 Using a RADIUS Server 166
- 9.1.1.2.1 Profile name 167
- 9.1.1.2.2 Settings 167
- Using a RADIUS Server 169
- 9.1.2.2.1 Descriptions 171
- 9.1.2.3.1 Descriptions 172
- 9.1.2.3.2 Access Reject 173
- 9.1.2.4.1 Descriptions 173
- 9.1.2.5.1 Descriptions 174
- RADIUS Server 175
- 9.2 Managing Certificates 177
- 9.2.1.1 Issued to 178
- 9.2.1.2 Current Usage 178
- 9.2.1.3 CRL 178
- 9.2.1.4 Delete 178
- 9.2.4 Default CA Certificates 179
- 9.2.4.1.4 Delete 180
- 9.2.5 Certificate Usage 181
- Managing Certificates 183
- Chapter 10 - Local Mesh 185
- 10.1 Key Concepts 186
- 10.2 Local Mesh Terminology 187
- Term Definition 188
- 10.2.2.1 Operational Modes 189
- 10.2.2.2 Node Discovery 189
- 10.2.2.3 Operating Channel 189
- 10.3 Local Mesh Profiles 191
- New Profile 192
- 10.3.1.1 Settings 193
- 10.3.1.2 Security 194
- 10.3.1.3 Addressing 194
- 10.3.1.3.3 Dynamic 195
- 10.3.1.3.3.1 Mode 195
- 10.3.1.3.3.2 Mesh ID 197
- 10.3.1.3.3.3 Minimum SNR 197
- 10.3.1.3.3.4 SNR Cost Per Hop 197
- 10.3.1.3.3.5 Allowed Downtime 197
- » An SNMP trap is sent 198
- 10.4.2 Maximum Range 200
- 10.5 Quality of Service 201
- 10.6 Configuration Summary 202
- Controlled Mode 203
- Figure 10-8: Group Management 204
- 10.7.2 Setting the Master AP 208
- 10.7.3 Setting the SLAVE AP 209
- 6 Save your configuration 211
- 10.7.5 Operation Verification 215
- 10.8.1 Dynamic Networks 217
- 11.1 Config File Management 220
- 11.1.1.2 Reset Configuration 221
- 11.1.2 Scheduled Operations 222
- -d pw=admin 223
- Config File Management 225
- 11.2 Firmware Updates 226
- 11.2.1 Immediate Update 227
- 11.2.2 Scheduled Update 227
- 11.3 Licenses 229
- Backup button 230
- Licenses 231
- Appendix A - Troubleshooting 233
- Appendix A -Troubleshooting 234
- In This Appendix: 237
- B.1 Introduction 238
- Introduction 239
- B.1.3 Using Special Commands 240
- 192.168.1.2 and 241
- Glossary 243
© 2020, manymanuals.com. All rights reserved. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals