Alvarion Wi^2 AP CLI Specifications Page 158
- Page / 248
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
136 BreezeMAX Wi² and BreezeACCESS Wi² System Manual
Chapter 8 - Management
8.3 SOAP
The AP provides a SOAP interface that can be used by SOAP-compliant client
applications to perform configuration and management tasks.
8.3.1 Configuring the SOAP Server
Select Management > SOAP to open the SOAP server configuration page. By
default, the SOAP server is enabled.
8.3.1.1 Server Settings
8.3.1.1.1 Secure HTTP (SSL/TLS)
Enable this option to configure the SOAP server for SSL/TLS mode. When
enabled, the Secure Sockets Layer (SSL) protocol must be used to access the
SOAP interface.
8.3.1.1.2 Using client certificate
When enabled, the use of a X.509 client certificate is mandatory for SOAP clients.
8.3.1.1.3 HTTP authentication
When enabled, access to the SOAP interface is available via HTTP with the
specified username and password.
Figure 8-5: SOAP Server Configuration
- BreezeMAX Wi² 1
- System Manual 1
- Document History 2
- Legal Rights 3
- Disclaimer 4
- Limitation of Liability 5
- Important Notice 7
- Compliances 9
- EC Conformance Declaration 10
- About This Manual 11
- Contents 15
- and BreezeACCESS VL Wi 16
- System Manual 16
- Chapter 4 - Getting Started 17
- Chapter 11 - Maintenance 21
- Appendix A - Troubleshooting 21
- 1.1 Introduction 24
- 1.2 Specifications 26
- 1.2.2 Sensitivity 27
- 1.2.3 8 dBi Omni Antenna 27
- 1.2.5 Mechanical 29
- 1.2.6 Electrical 29
- 1.2.7 Connectors and LEDs 30
- 1.2.8 Environmental 30
- 1.2.9 Standards Compliance 31
- 2.1 Hardware Description 34
- 2.1.1 Bottom Panel 35
- 2.1.2 Top Panel 36
- 2.1.3 LED Indicators 36
- 2.1.3.2 Controlled Mode 37
- 2.2 Installation Requirements 38
- Installation Requirements 39
- 2.3 Installation 41
- Installation 43
- BreezeACCESS SU-ODU 46
- 2.3.5 Mounting the Wi² Unit 50
- 2.3.9.2 Configuring the Wi² 54
- Extender 57
- 3.1.1 Ethernet Port 58
- 3.1.2 Console Port 58
- 3.1.3 Grounding Point 58
- 3.1.4 Water Tight Test Point 58
- Ethernet 59
- Link/Activity 59
- 3.2 Installation Requirements 60
- Thread the steel-band 62
- Mounting the Wi² Extender ODU 63
- Secure the rectangular 64
- Wi² Extender using the 64
- Strap the steel-band 65
- Tighten the steel-band 66
- Extender to the pole 66
- 3.4.1 Grounding Wire 67
- Ethernet cable 70
- AC power 70
- 4.1 Introduction 74
- 4.2 Configuration Procedure 75
- Configuration Procedure 77
- 5.1 Key Concepts 84
- 5.1.1.1 User Authentication 85
- Service Controller 88
- 5.1.3 Management with VLANs 89
- 5.3.1 Virtual AP 94
- 5.3.2 Egress VLAN 95
- 5.3.4 Wireless Protection 97
- 5.3.4.2 802.1X 98
- Enabled Disabled 100
- 5.3.8 Wireless IP Filter 101
- 5.4 Virtual Network Data Flow 102
- 5.4.1 Stand-alone Deployment 103
- Controller 103
- 5.4.2.3 Egress 104
- 5.4.3.1 Ingress 104
- 5.4.2.2 Features 104
- 5.4.3.2 Features 105
- 5.4.3.3 Egress 105
- 5.5 Quality of Service (QoS) 106
- 5.5.1.2 802.1p 107
- 5.5.1.5 TOS 108
- 5.5.1.6 IP QoS 108
- 5.5.1.7 Disabled 109
- 5.5.1.8 QoS Example 109
- In This Chapter: 111
- 6.1 Wireless Coverage 112
- 6.1.2.2 Antenna Configuration 113
- 6.1.2.3 Interference 113
- 6.1.3.2 Selecting Channels 115
- Wireless Coverage 117
- 6.2 Conducting a Site Survey 119
- Conducting a Site Survey 121
- 6.3 Radio Configuration 122
- 6.3.1.1 Operating mode 123
- 6.3.1.2 Wireless Mode 123
- 6.3.1.3 Channel 123
- 6.3.1.4 Interval 124
- 6.3.1.5 Time of Day 124
- 6.3.1.7.2 RTS Threshold 125
- 6.3.1.7.3 Multicast Tx Rate 125
- 6.3.1.7.4 Antenna Selection 125
- 6.3.1.7.5 Beacon Interval 126
- 6.3.1.7.6 Spectralink VIEW 126
- 7.1 Port Configuration 130
- Port Configuration 131
- 7.1.3 Port Configuration 132
- 7.1.3.2 Link 133
- 7.2 VLAN Support 134
- 7.2.3 VLAN Bridging 135
- 7.2.4 VLAN Configuration 136
- 7.2.4.1 General 137
- 7.2.4.2 Assign IP Address Via 137
- 7.3 Bandwidth Control 138
- 7.5.1 DNS Servers 140
- 7.5.2 DNS Advanced Settings 140
- 7.5.2.3 DNS Switch Over 141
- 7.5.2.4 Logout Host Name 141
- 7.6 IP Routes 142
- 7.6.1.2 Default Routes 143
- 7.7 IP QoS 144
- 7.7.1.1 Settings 145
- 7.7.2 Example 146
- 4 Select Save 148
- Chapter 8 - Management 149
- 8.1 Management Tool 150
- Management Tool 151
- 8.1.3.3 Login Control 152
- 8.1.3.4 Web Server 153
- 8.1.3.5 Security 153
- Auto-refresh icon 154
- 8.2 SNMP 155
- 8.2.1.1 Attributes 156
- 8.2.1.2 Agent 156
- 8.2.1.3 Security 156
- 8.2.1.4 Traps 157
- 8.3 SOAP 158
- 8.3.1.2 Security 159
- 8.4.1 Configuring CLI Support 160
- 8.5 System Time 162
- 8.6 Country 163
- Chapter 9 - Security 165
- 9.1 Using a RADIUS Server 166
- 9.1.1.2.1 Profile name 167
- 9.1.1.2.2 Settings 167
- Using a RADIUS Server 169
- 9.1.2.2.1 Descriptions 171
- 9.1.2.3.1 Descriptions 172
- 9.1.2.3.2 Access Reject 173
- 9.1.2.4.1 Descriptions 173
- 9.1.2.5.1 Descriptions 174
- RADIUS Server 175
- 9.2 Managing Certificates 177
- 9.2.1.1 Issued to 178
- 9.2.1.2 Current Usage 178
- 9.2.1.3 CRL 178
- 9.2.1.4 Delete 178
- 9.2.4 Default CA Certificates 179
- 9.2.4.1.4 Delete 180
- 9.2.5 Certificate Usage 181
- Managing Certificates 183
- Chapter 10 - Local Mesh 185
- 10.1 Key Concepts 186
- 10.2 Local Mesh Terminology 187
- Term Definition 188
- 10.2.2.1 Operational Modes 189
- 10.2.2.2 Node Discovery 189
- 10.2.2.3 Operating Channel 189
- 10.3 Local Mesh Profiles 191
- New Profile 192
- 10.3.1.1 Settings 193
- 10.3.1.2 Security 194
- 10.3.1.3 Addressing 194
- 10.3.1.3.3 Dynamic 195
- 10.3.1.3.3.1 Mode 195
- 10.3.1.3.3.2 Mesh ID 197
- 10.3.1.3.3.3 Minimum SNR 197
- 10.3.1.3.3.4 SNR Cost Per Hop 197
- 10.3.1.3.3.5 Allowed Downtime 197
- » An SNMP trap is sent 198
- 10.4.2 Maximum Range 200
- 10.5 Quality of Service 201
- 10.6 Configuration Summary 202
- Controlled Mode 203
- Figure 10-8: Group Management 204
- 10.7.2 Setting the Master AP 208
- 10.7.3 Setting the SLAVE AP 209
- 6 Save your configuration 211
- 10.7.5 Operation Verification 215
- 10.8.1 Dynamic Networks 217
- 11.1 Config File Management 220
- 11.1.1.2 Reset Configuration 221
- 11.1.2 Scheduled Operations 222
- -d pw=admin 223
- Config File Management 225
- 11.2 Firmware Updates 226
- 11.2.1 Immediate Update 227
- 11.2.2 Scheduled Update 227
- 11.3 Licenses 229
- Backup button 230
- Licenses 231
- Appendix A - Troubleshooting 233
- Appendix A -Troubleshooting 234
- In This Appendix: 237
- B.1 Introduction 238
- Introduction 239
- B.1.3 Using Special Commands 240
- 192.168.1.2 and 241
- Glossary 243
© 2020, manymanuals.com. All rights reserved. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals