Alvarion BreezeACCESS 4900 Specifications Page 161
- Page / 257
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 - Operation and Administration Menus and Parameters
BreezeACCESS 4900 135 System Manual
Forced: The Noise Floor value is set manually to the value configured for the
Forced Value parameter (see below). Typically this mode should be used only
for special testing purposes.
Automatic with Minimum Value: If the calculated Noise Floor using the
built-in mechanism is higher than the value configured for the Forced Value
parameter, the calculated value will be used. Otherwise, the Forced Value will
be used.
The default option is Fully Automatic.
4.2.6.2.17.2 Forced Value
The Forced Value parameter enables configuring the Noise Floor to be used if the
selected Calculation Mode is Forced. This is also the minimum value to be used if
the selected Calculation Mode is Automatic with Minimum Value.
If you decided to change the calculation mode to Automatic with Minimum Value
and you still experience problems in the link (long association time, exceptionally
low throughput), try to improve it by increasing the configured Forced Value.
The available range is from -107 to -55 (dBm)
The default value is:
5 MHz bandwidth: -102 (dBm)
10 MHz bandwidth: -99 (dBm)
4.2.6.2.17.3 Show Noise Floor Calculation
Select this option to view the current values of the Noise Floor Calculation
parameters and the Noise Floor Current Value (the actual current value used by
the device).
4.2.6.2.18 Calibration of Noise Floor Indication
The Calibration of Noise Floor Indication feature has been introduced to overcome
possible inaccuracies in the Noise Floor Calculation mechanism. The calibrated
Noise Floor Indication is used for correcting the displayed Noise Floor values
versus the values that are calculated/used by the internal noise floor calculation
mechanism.
The Calibration of Noise Floor Indication submenu includes the following options:
4.2.6.2.18.1 Run Calibration
Select the Run Calibration option to perform a new calibration process. Typically
this should be performed for a new unit when Factory calibration is not available,
- BreezeACCESS 1
- System Manual 1
- Document History 2
- Legal Rights 11
- Disclaimer 12
- Limitation of Liability 13
- Electronic Emission Notices 13
- FCC Radiation Hazard Warning 14
- Antenna Compliance Statement 14
- Safety Considerations 14
- Line Voltage 15
- Important Notice 16
- About this Manual 18
- Appendix F - Troubleshooting 19
- Contents 20
- System Description 27
- In This Chapter: 28
- 1.2 Base Station Equipment 31
- 1.3 Subscriber Unit 34
- 1.4 DC Power Injector 35
- 1.6 Networking Equipment 38
- 1.7 Management Systems 39
- 1.8 Specifications 41
- 1.8.2 Data Communication 42
- 1.8.5 Physical and Electrical 44
- 1.8.5.1.2 Connectors 45
- 1.8.5.1.3 Electrical 45
- 1.8.5.2.1 Mechanical 45
- 1.8.5.2.2 Connectors 46
- 1.8.5.2.3 Electrical 46
- 1.8.5.3.1 Mechanical 47
- 1.8.5.3.2 Connectors 47
- 1.8.5.3.3 Electrical 48
- 1.8.7 Environmental 49
- Installation 50
- 2.1 Installation Requirements 52
- 2.1.1.2.2 AU-E-BS Access Unit 53
- Figure 2-3: 61
- Equipment 68
- Commissioning 74
- 3.1.1 Initial Configuration 76
- Section 3.3 77
- Table 3-1: Basic Parameters 77
- 3.1.2 Country Code Selection 78
- Maximum Modulation Level 82
- 3.4 Operation Verification 84
- Base station) 87
- (Modular Base Station) 87
- Operation and Administration 88
- 4.1.2 Common Operations 92
- 4.2 Menus and Parameters 93
- 4.2.2.1 Show Unit Status 94
- 4.2.3 Unit Control Menu 99
- 4.2.3.1 Reset Unit 100
- 4.2.3.2 Default Settings 100
- 4.2.3.2.1 Set Defaults 101
- Parameters Group Parameter 103
- 4.2.3.3 Change Unit Name 105
- 4.2.3.4 Change Password 105
- 4.2.3.5 Flash Memory Control 105
- 4.2.3.6 Log Out Timer 106
- 4.2.3.9 Event Log Menu 107
- 4.2.3.9.4 Event Log Upload 108
- 4.2.3.10 Feature Upgrade 109
- 4.2.3.11 SW Version Download 110
- 4.2.3.13 LED Mode 113
- 4.2.3.13.2.1 LED 1 to 8 114
- 4.2.3.13.2.1.1Threshold Type 114
- 4.2.3.13.2.1.2Threshold Mode 114
- 4.2.4.1 IP Parameters 115
- 4.2.5 Site Survey Menu 118
- 4.2.5.1 Traffic Statistics 119
- 4.2.5.1.2 WLAN Counters 120
- » Beacons (AU only) 121
- 4.2.5.2 Ping Test 124
- SNR_Memory_Factor 125
- 4.2.5.4 MAC Address Database 126
- ◊ The MAC address of the AU 127
- ◊ The MAC address of the SU 131
- 4.2.5.8 Link Capability 133
- 4.2.6.1 IP Parameters 135
- 4.2.6.1.4 DHCP Client 136
- 4.2.6.1.5 Show IP Parameters 137
- 4.2.6.2.1 ESSID Parameters 137
- 4.2.6.2.1.1 ESSID 139
- 4.2.6.2.1.2.2 Operator ESSID 139
- 4.2.6.2.3.1 Sub-Band Select 141
- 4.2.6.2.3.2 Frequency 141
- 4.2.6.2.4.1 Sub-Band Select 141
- 4.2.6.2.5.1 Best AU Support 143
- 4.2.6.2.7.1 Transmit Power 146
- 4.2.6.2.7.1.1 Transmit Power 146
- 4.2.6.2.7.4.1 ATPC Option 149
- 4.2.6.2.8 Antenna Gain 150
- 4.2.6.2.9.3 Fairness Factor 152
- 4.2.6.2.13 Spectrum Analysis 155
- 4.2.6.2.16.4 OFDM Weak Signal 159
- 4.2.6.2.17.1 Calculation Mode 160
- 4.2.6.2.17.2 Forced Value 161
- 4.2.6.2.18.1 Run Calibration 161
- 4.2.6.3.7.1 Send SNMP Traps 166
- 4.2.6.4 Bridge Parameters 167
- 4.2.6.4.1 VLAN Support 168
- 4.2.6.4.1.3 VLAN Link Type 171
- 4.2.6.4.1.3.2 Trunk Link 171
- 4.2.6.4.1.3.3 Hybrid Link 172
- 4.2.6.4.1.9.1 VLAN Rule # 179
- 4.2.6.4.1.9.2 Show Rule List 183
- 4.2.6.4.2.1 Filter Options 183
- 4.2.6.4.4 Bridge Aging Time 186
- 4.2.6.5.1 RTS Threshold 190
- 4.2.6.5.9 Burst Mode 194
- 4.2.6.5.9.1 Burst Mode Option 195
- 4.2.6.6 Service Parameters 202
- 4.2.6.6.3.2.3 DSCP Threshold 211
- » RTP & RTCP 212
- » RTP Only 212
- 4.2.6.6.3.3.3 TCP Port Ranges 213
- 4.2.6.6.3.4.3 IP Range Mask 215
- 4.2.6.6.4.1 DRAP Support 219
- 4.2.6.6.4.2 UDP Port 219
- 4.2.6.6.4.4 DRAP TTL 219
- 4.2.6.7 Security Parameters 220
- 4.2.6.7.3 Security Mode 221
- 4.2.6.7.6 Key # 1 to Key # 4 222
- 4.2.6.8.1 Select Country Code 223
- Appendix 224
- Main Version Number :4.5.16 227
- Shadow Version Number :5.0.13 227
- SU Cable 233
- Parameters Summary 236
- In This Appendix: 237
- E.1 Parameters Summary 238
- E.1.2 IP Parameters 240
- E.1.5 Bridge Parameters 244
- E.1.6 Performance Parameters 247
- E.1.7 Service Parameters 248
- E.1.8 Security Parameters 251
- Troubleshooting 252
- F.2 SU Association Problems 255
- F.3 Low Throughput Problems 256
- SNR Maximum Modulation Level 257
Related products and manuals for Routers Alvarion BreezeACCESS 4900
Routers Alvarion BreezeNET DS.11 User's Guide
(117 pages)
(117 pages)
Routers Alvarion BreezeACCESS 4900 User Manual
(119 pages)
(119 pages)
Routers Alvarion BreezeACCESS VL User Manual
(10 pages)
(10 pages)
Routers Alvarion BreezeNET DS.11 User Manual
(66 pages)
(66 pages)
Routers Alvarion BreezeNET DS.11 User's Guide
(192 pages)
(192 pages)
© 2020, manymanuals.com. All rights reserved. | 0.250 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals